Bifold Closet Doors size

How do I determine rough opening sizes for common closet door sizes?

Bifold Closet Doors Sizes

The closet doors are most likely listed in actual finished opening size. However it is a good idea to use a tape measure to check 100% for sure. Some doors are made a little oversize to allow trimming into final size for the specified opening size. Other doors may very well be made a small amount undersize to allow for the necessary clearances needed for a finish sized door within the specified opening size.

The installation instructions that come with many doors will be your first go-to source of information regarding the finished opening size is applicable to the doors.

As far as the rough opening size . . . That is totally dependent on your individual situation. Some things that will affect rough opening size are:

= The size and thickness of the door jamb material for cases where a jamb is used.

= Style of jamb used and how the door itself will interact with the jamb.

= Squareness and true of the rough opening. A rough opening that is out of square by some amount will require the jamb to shimmed away from the studs in a way to bring the jamb into square and plumb. This may increase the rough opening size by the amount of shimming that is required.

Source: diy.stackexchange.com

Slide-Co Slide-Co 164183 Bi-Fold Door Repair Kit with 2 Door Set
Home Improvement (Slide-Co)
  • Repairs 2 doors
  • Fits a 7/8in. wide track system
  • Repairs a 3/8in. diameter system
  • Easy to install

You might also like:

Home Depot | Home Services & …
Home Depot | Home Services & …

Can somebody help me find bifold closet doors

That can cover an 84 inch door opening. I just want plain white six panel doors. Masonite is the most popular but the max is a 72inch opening. I dont want to put panels on the sides - can anyone recommend another company that would make a bigger size, special order (i need custom height too - 92 inches)
thanks.

Now you're confusing things- you say it's 8'8"

Describe the framing "on top of/behind the curtain track", which wouldn't have anything to do with the width of the opening...
regardless, that's a pretty big opening to install bifolds in...it can be done, but any of the various options are going to have some drawbacks-
You could go with four 26" panels (not a standard bifold panel size but what door shops do in many cases is to just hinge shutters together, and they come in all kinds of interim sizes and panel/louver designs)...
Problem is that when open, they will stick both into and out of the closet over a foot

Stanley Hardware Stanley Hardware 48-Inch Bifold Set #402044
Home Improvement (Stanley Hardware)
  • Designed for 1-inch thick panels; total width of 48 inches
  • Supports 2 doors weighing up to 30 pounds each
  • White finish
  • Includes a pair of snuggers, top pivots, guide wheels, bottom pivots, hinges, knobs and aligners
Door H Closet Door Spring
Home Improvement (Door H)
  • Closet Door Spring
  • BIFOLD SPRING
PRIME-LINE PRODUCTS/SLIDE-CO Prime-Line Folding Door Hardware Kit
Home Improvement (PRIME-LINE PRODUCTS/SLIDE-CO)
  • For 24 to 36 2 door systems
  • For 7/8 to 1-3/8 thick doors up to 35 lbs. per panel
  • 35-3/4 overall track length
  • Top hung surface mount steel track with off white finish
  • Boxed

Related posts:

  1. Bifold closet doors Home Depot
  2. Bifold Doors sizes
  3. Bifold closet Door parts
  4. Closet Doors Lowes
  5. Bypass closet doors Lowes

  • Avatar niner_72601 Partially replace my existing cabinets?
    Jan 21, 2007 by niner_72601 | Posted in Decorating & Remodeling

    I have cabinets in my kitchen that are painted.......i want to go oak face frame and doors...............can i pull off the existing face frame, and replace with an oak one......my question is......whats the best way to build the frame......dowels?

    • The face frames may be a beotch to replace; they were built on the cabinet boxes, or glued to them. Just depends on the construction. The best way is to use pocket screws. There is an angled hole (pocket) drilled into th …e fancy machine).

      Otherwise, you just apply the boards individually to the cabinet box and pin the edge that hangs down with a finish nail (not the best method, but it's done on built in shelves everyday).